Fence Fix – Fixing a Broken Fence Post

It appears to be an intimidating task to replace a broken fence article but it isn’t quite as tough as it might seem. It will take a little bit of elbow grease and a couple of straightforward tools you probably already have in the garage or shed Chattanooga Home Remodeling. Where do you begin? You first have to rate the undertaking and also the harm.

Fence Fix

Did the article rust and only crack or was it sheered off because of horrible weather conditions? Is there still a remaining stump or can it be broken off on the floor or concrete degree? Don’t be frightened, the job is rather difficult and should only require approximately 1 to 2 hours of your own time to finish and your weapon will probably be good as new.

Bridge, Asphalt, Site, Rehabilitation

Issue Level: Moderate

  • Shovel
  • Pry Bar
  • Amount
  • Bags of Gravel

Ordinarily, most fence posts are put into the floor utilizing concrete although others are set up using packed dirt from the fence post gap. If you don’t see concrete in the bottom level, take a typical shovel and dig a couple of inches near the broken place location and see if you strike concrete.

There are various schools of thought in regards to eliminating a present post. Many folks prefer the smash and grab procedure that’s simply having a hammer and chisel or pry bar to break the concrete to little pieces and pull them from the present hole one.

The method does work but is a good deal of work and it might choose between one (1) and 2 (two ) hours of labor to extract the concrete in the hole. It’s fine when you’ve got one pole to substitute but when there are numerous, the job involved is quite tedious and exhausting and you will find better ways.

The way that I prefer is to choose a very long, skinny bladed spade and dig the dirt only to the side of this cement exposing the other side of the cement block. Just make sure you pile the dirt near the pit since the dirt that you eliminate will be utilised to re-pack the hole when the pole along with concrete block is taken out of the ground. This allows for a pocket as broad as the concrete cube.

If a bit or stump in the present place remains set up, you may use it and begin transferring the concrete block back and on with the new pocket area you created. Be careful and be sure that you lift with your legs since the concrete block may weigh up to eighty (80) pounds.

In case the present post or article stump is no more connected to the concrete, then you need to be able to use a pry bar or perhaps your spade to move the present concrete block back and forth in a similar way loosening it out of its initial placement. After the block is movable, utilize exactly the exact same procedure as stated previously but be careful to use proper lifting techniques when eliminating the concrete. A physician’s visit isn’t prescribed in this undertaking.

Make sure you pack the dirt as it will offer the lateral support to your new post as it’s set up. The concrete you use while you place the new article will offer lots of support as well as attaching the present fence arrangement but the greater you package the dirt, the greater the outcome.

From here, you should take your clam digger or pole digger or whether you don’t have one, simply use your spade and dig approximately two (2″) inches in the base of the hole. Then add loose sand in these two (2″) inches for drainage to keep away water from the base of the post.

If you don’t have or didn’t buy a bag of dirt once you bought your replacement concrete and post, don’t stress. The cement has gravel inside and certainly will operate but the gravel will not create the drainage more effective. As soon as you have the foundation set up, now is the time to put in the replacement article.

Grab your replacement pole and centre it at the hole. In case you’ve got a helper, have them hold the article and ensure it lines up properly with the fence as well as the old article you simply eliminated. As soon as you’ve got it in the appropriate place, start an eighty (80) pound bag of Quickrete concrete and then put it dry to the hole. Ensure that you are wearing eye protection also to protect your mouth so that you don’t inhale the dust which typically spews from the hole because you pour into the mix.

Pour all the contents to the hole. Grab your garden hose or a bucket of water and get started pouring water to the pit and be sure that you pour round the new pole in a circular layout to be certain that to receive the entire surface of the cement wet. The water will start to bubble since it begins leaking into the bottom.

Continue to add water till it pools somewhat. It’ll absorb through the mixture. Now, choose your pry bar or a sheet of rebar or possibly a sturdy stick and begin poking the concrete mix to help get the water to flow down to the bottom in addition to eliminate the air bubbles which form. It’s OK when the water pools somewhat but do not make the mix too wet because it will take more time to set.

Take your degree and ensure the post remains in its vertical vertical position. It’s beneficial if you check on several sides and be certain that the bubble on the degree is at the center and between the marks. When the article is flat, use pieces of timber to make a stand of types at the base to keep the article from moving while the concrete sets up immediately. The concrete will start setting and based upon the climate ought to be prepared the following day to re-hang the fencing bits.

In case the place goes, wiggle it in the vertical position and then using your rod or pry bar, proceed to the concrete mixture around so it rolls the pole on either side in the floor with no openings. If gaps form, you might have to bring a little bit of additional water to make the mix more liquid. Any potable water will probably be absorbed into the concrete and encompassing dirt and evaporate because of the concrete places.

The following day, you ought to be able to re-affix the fencing into the article and it ought to be good as new. Before you attach the fence bits, you need to inspect the height of this fence post compared to the other articles on your fence line. Based upon the remainder of your weapon, then you might choose to utilize an electric or hand saw to cut the new post to coincide with the other articles in your weapon.

If the article doesn’t have to be cut, then it’s possible to join the old fence bits to the news article. Make sure you use screws once you attach the fencing back to the new article to guarantee a more secure connection than claws that could pull out from bad or windy weather conditions during time inducing ethics problems.

Leave a Reply